Cwejman BLD bass and drum module

CWBLD

Nowy produkt

The BLD has all components and functions necessary for generating bass, lead and drum sounds but with focus on bass drum sounds. 
The BLD contains a main sound generator (Oscillator), a noise generator and modifiers such as low pass filter, amplifier and two transient (contour) generators.

Więcej szczegółów

Na zamówienie

2 965,86 zł brutto.

Share:

The BLD has all components and functions necessary for generating bass, lead and drum sounds but with focus on bass drum sounds.
The BLD contains a main sound generator (Oscillator), a noise generator and modifiers such as low pass filter, amplifier and two transient (contour) generators.
The oscillator has two manual pitch controllers (FINE, COARSE) and two inputs for controlling the pitch by external signals: FM1 (levelled, bipolar pre-patched to transient generator AR) and FM2 (calibrated to 1 Volt/octave).
Waveforms and mix between shapes is controlled manually from triangle, mix between triangle and pulse, pulse, mix between pulse and saw tooth and saw tooth.
Oscillator level is controlled manually from 0 thru nominal signal strength to saturated (curved, for more punch).
Pulse width is controlled manually and by an external signal (PWM).
LOW PASS FILTER has two audio inputs marked OSCILLATOR LEVEL and NOISE LEVEL, The CUTOFF frequency is controlled manually, transient generators AR and AHR and by CUTOFF pre-patched to FM2 CV input.
NOISE GENERATOR is connected to the low pass filter and to the amplifier (NOISE LEVEL).
The noise generator can be routed in to the amplifier (PRE) or directly to the output AMP (POST).
The noise generators level is also controlled by pre-patched AR generator thru input NOISE LEVEL.
AR and AHR transient generators are activated manually by the push button TRIG and/or by an external signal(input TRIG).
Attack, Hold and Release are manually controlled and by an external signals connected to inputs A1, R1 (AR) and A1, HOLD and R2 (AHR).
AMPLIFIERs gain is controlled by mix of AR and AHR and by an external signal connected to the input VELOCITY.

       technical details
Width 24HP
       Inputs: 
FM1 
FM2 
TRIG 
PWM 
SYNC 
Attack 1 
Release 1 
Noise Level 
Attack 2 
Hold 
Release 2 
Velocity
       Outputs: 
AR (envelope 1) 
AHR (envelope 2) 
LPF 
AMP

Powiązane produkty

It's a dual envelope generator with two identical, independent ADSR units which can be both triggered simultaneously by one single trigger due to a normalized jack. All parameters (attack, decay, sustain release and the output level) can be voltage controlled. Besides short A, D and R times a switchable characteristic of the attack for punchy and crisp...
2 699,81 zł
The Audio Interface AI-2 is a very helpful tool for converting unbalanced audio signals into balanced and vice versa.
1 461,11 zł
The Audio Processor AP-1 is an indispensable module for everybody who wants to process external audio signals in modular systems. The AP-1 provides you with three sections: Pre-amp, envelope follower and compressor
2 891,69 zł
The ATT-4 is a fourfold attenuator with additional offset-switches.  Its primary task is the attenuation of modulations  in case modulation inputs don't have their own attenuators.
1 151,46 zł
The CRV-24 is a four band crossover with 24 dB/octave slope for all four bands. Crossover frequencies can be controlled manually and by attenuable CV signals.
2 878,61 zł
CTG-VC, a single complex voltage controlled transient generator.  The envelope generator provide control voltages that can be used for dynamic change of all voltage controlled parameters, such as; frequency, amplitude, pulse width, cutoff.
2 215,66 zł
Two identical, flexible LFOs with very innovative sync possiblities  and an enormous frequency range.  The cherry on top is the amplitude- and ring modulation between the LFOs.
2 695,45 zł
The DMF-2 module consists of two identical filters with two modes:  lowpass and a quasi-bandpass which are available simultaneously at separate outputs.
2 638,72 zł
The compressor module VC-FC is the stereophonic brother of Cwejman´s VC forward compressor. It´s the first of its kind because so far no manufacturer developed a fuly voltage controlled compressor, even more not in stereo!
3 855,62 zł
The FSH-1 module is a voltage controlled frequency shifter in studio quality. Unlike to other products on the market there is no bleedthrough of the internal oscillator and no audible noise!
2 965,86 zł
Dual voltage controlled cross-fade mixer. Main purpose is crossfading between original and effect-signal so the module is like an insert with a dry/wet control. But also normal cross-fading between two different sound sources is somehow possible.
2 028,14 zł
If You don't want scratches on Your modules , You'll need this!  ⌀  3M washers.
21,64 zł

Przejdź do góry