Doepfer Dark Time Analog Sequencer red LEDs

DODARKT

Nowy produkt

Dark Time is an 2 x8 steps analog sequencer with CV/Gate, USB and Midi interface. It is planned in the first place as an add-on for the Dark Energy but may be used even in combination with other Midi, USB or CV/Gate equipment too

Więcej szczegółów

dostępny

2 093,54 zł brutto.

Share:

Doepfer Dark Time - analog sequencer with 16 steps, two rows with 8 controls each, for each step: rotary thomann control, red LED, three-position switch On/Off/Skip and three-position switch Stop/Continue/Jump, several operating modes: 1x16 (i.e. the two rows are daisy-chained), 2x8 (i.e. both rows run in parallel), custom mode, several running directions: forward, backward and random, quantization, transpose via switch, timing thomann control, selected by a three position switch: internal via built-in clock oscillator with frequency and pulse width controls, external via Midi/USB and # external via analog clock/start/stop, analog interface for CV/gate/clock/Start-Stop (inputs and outputs, 3.5 mm miniature jack sockets), MIDI I/O, USB connection, thomann powered via external power supply (12 AC/min. 400mA) for 230V. Red LED edition.
                     Features overview
    two rows with 8 controls each
    for each step:
        - rotary control (same knob type as Dark Energy)
        - red LED
        - three-position switch On/Off/Skip
            On = trigger signal is active for this step
            Off = no trigger for this step
            Skip = step is skipped
        - three-position switch Stop/Continue/Jump
            Stop = sequence stops here
            Continue = sequence continues
            Jump/Reset:
If only one of the 16 toggle switches is in the Jump position a Reset is carried out (i.e. sequence jumps to stage 1)
                If two or more of the switches are in the Jump position the sequence jumps to the next step with the switch in the Jump position and then continues from this position (until another step with the switch in the Jump position is reached and then the same procedure is carried out again)
    several operating modes:
        1x16 (i.e. the two rows are daisy-chained)
        2x8 (i.e. both rows run in parallel)
        1-8 Combi (lower row set individual gate lenght of the upper row)
    several running directions:
        forward
        backward
        random
    CV scaling: 1V/Octave standard (note: not suitable to control devices with Hz/V scale !)
    several voltage / tuning ranges: 1V, 2V, 5V (corresponding to 1/2/5 octaves)
    gate voltage 0/+5V (please refer to the remarks below
concerning devices with S-Trigger or Korg MS10/MS20)
for units manufactured later than early 2012 (from serial number 120240) the output voltage for Gate/Clock/Reset/Start-Stop can be set to +12V by means of an internal jumper (the corresponding interface boards are marked V2/2011 or V3/2012). The following document describes the modification procedure in detail: Dark_Time_12V_Gate.pdf.
quantization on/off/custom scale  (custom scale not yet available in the first firmware version)
when quantization is "off" the resolution is still 10 bit (i.e. 1024 steps over the full rotating range of each potentiometer), from this the term "quantization off" is not fully correct, with quantization "on" the resolution is 13/25/61 steps for 1/2/5 octaves
transpose via switch (-1/0/+1 octave), Midi/USB or external CV input
timing control, selected by a three position switch:
    internal via built-in clock oscillator with frequency and pulsewidth controls
    external via Midi/USB
    external via analog clock/start/stop
analog interface for CV/gate/clock/Start-Stop (inputs and outputs, 3.5 mm miniature jack sockets)
Midi interface
USB interface (power supply via USB is not possible)
optically adapted to Dark Energy (same knobs, same depth and height, same wooden side plates and so on)
Powered via external power supply (12V AC/min. 400mA) for 230V
powering the device via USB is not possible, because the analog circuits require a dual voltage (+/-12V).

Powiązane produkty

The Tiptop Audio - Z8000 Matrix Sequencer is a powerful tool in a small package. 
1 725,76 zł
The Touch-Sequencer is the first in a series of Modcan modules to be adapted for the Euro Rack format.
3 607,22 zł
A true analog step sequencer with three rows of eight steps for generating control voltages and trigger signals. The RS-200 impresses with an internal, voltage controllable clock generator, portamento, reset start/stop functions and a voltage influenced skip feature
2 725,97 zł
If You don't want scratches on Your modules , You'll need this!  ⌀  3M washers.
21,64 zł

Przejdź do góry