Mode.M Modular Shop

Follow @mode_modular Tweets by mode_modular



Dostępny na zamówienie

Produkt PDF

Ocena(0 głosów)

Module A-171-2 is a voltage controlled slew limiter with a lot of additional features beyond a simple slew limiter. It's mostly a licensed copy of Ken Stones VCS which is in turn based on the Serge VCS.



Zakupy z Mode.M Modular są zawsze bezpieczne.
Połączenie z serwerem jest szyfrowane z użyciem klucza SSL

   Szybka dostawa kurierem lub paczkomatem

   miesiące gwarancji

   Darmowa dostawa do Polski od 500 PLN

Produkt dostępny na zamówienie



Opis

These are the most important features:
    Manual control of the Slew-Up time
    CV control of the Slew-Up time with polarizer
    Switch for linear/exponential shape of the rising section of the response curve
    Manual control of the Slew-Down time
    CV control of the Slew-Down time with polarizer
    Switch for linear/exponential shape of the falling section of the response curve
    Signal input: the "to-be-slewed" signal
    CV Up Input, affected by the CV Up Control and the corresponding exp./lin. switch
    CV Down Input, affected by the CV Down Control and the corresponding exp./lin. switch
    CV Up and CV Down sockets are normalled
    exponential CV input: named "V/Oct" in the original design but as it's not really exactly 1V/Oct we will name this input probably "exp.CV", mainly used for VCLFO/VCO applications in cycle mode or as common exponential control for both up and down times in slew mode
    Trigger input: used for envelope generation or retrigger in VCLFO/VCO mode, a pulse at the trigger input will start the envelope or retrigger the VCLFO/VCO
    End output: turns high as the output falls below about 20mV, turns low as the outputs goes beyond about 3.5V, in cycle mode a rectangle signal is generated
    Cycle on/off switch: when "on" the End output is internally connected to the Trigger Input to generate cyclic signals like an VCLFO/VCO
    Output: the signal output of the module
    LED display: displays the slew limiter output signal
Typical applications:
    VC Slew Limiter / VC Portamento / VC Low Pass Gate
    Cycle switch = off, no trigger signal applied to Trig socket:
    Voltage controlled Slew limiter or portamento generator: the signal applied to the signal input is "slewed". The slew up and down times are controlled manually by means of the Up and Down controls, the effect of the CV Up and CV Down control voltages are controlled by the CV Up and CV Down controls, in exponential mode these controls also affect the slew shape (see symbols at the CCW and CW positions of the controls)
    If an audio signal is applied an short slew rates are chosen
the module works as a simple VCF/VCA combo
    A/D Envelope Generator / Pulse Delay / Subharmonic Generator
    Cycle switch = off, trigger signal applied to Trig socket, no input signal:
    Simple Attack/Decay envelope Generator, the rise and fall times are controlled like the slew up/down times above, including the shape of the falling/rising slope of the envelope, the exp. CV input can be used to change both attack and decay simultaneously
    At the End output a pulse appears as the end of the envelope is reached (less than about 20mV), this can be used as a pulse delay
    If a series of triggers are applied to the VCS faster than the total rise and fall times, the module will divide the incoming signal by a whole number. In the audio range the output will be the sub-harmonic series.
    VCLFO / VCO
    Cycle switch = on, no trigger signal applied to Trig socket, no input signal:
    Voltage controlled LFO/VCO, the rise and fall times of the waveform are controlled like the slew up/down times above, including the shape of the falling/rising slope
    the exp. CV input can be used like the CV input of a VCO or
VCLFO, the response is exponential but not exactly 1V/oct
Width: 8 TE / 8 HP / 40.3 mm
Depth: 60 mm (measured from the rear side of the front panel)
Current: +30mA (+12V) / -30mA (-12V)

Kategorie: , , , , .